AbstractAbout AuthorsReferences
A solution is proposed for the installation of overlap of a low-rise building by the method of element-by-element segment printing on a 3D construction printer with subsequent rotation of the structure to the design position. The object of the study is a rotating section of the overlap, consisting of upper and lower belts connected by a wave-like element (“connecting grid”). For the object of the study, it was found that when calculating by the finite element method, the method of modeling with “plates” (type 42/44) + AJT in the appropriate places reduces the complexity of creating a computational model compared to modeling with volumetric bodies (type 36) while maintaining identical calculation results. When determining the optimal configuration of the “connecting grid”, it was found that the wave-shaped connecting element has advantages over the cross-wave element and the perpendicular connecting element. Also in this paper, a conclusion is made about the optimal angle of inclination of the “connecting grid” in relation to the belts, which is 26–27о.
I.O. RAZOV, Candidate of Sciences (Engineering) (This email address is being protected from spambots. You need JavaScript enabled to view it. ),
V.G. SOKOLOV, Doctor of Sciences (Engineering),
A.V. DMITRIEV, Candidate of Sciences (Engineering),
S.A. ERENCHINOV, Candidate of Sciences (Engineering)
V.G. SOKOLOV, Doctor of Sciences (Engineering),
A.V. DMITRIEV, Candidate of Sciences (Engineering),
S.A. ERENCHINOV, Candidate of Sciences (Engineering)
Tyumen Industrial University (38, Volodarskogo Street, Tyumen, 625000, Russian Federation)
1. Zas’ko V.V.,Ratushnaya E.V. Application of 3D printers in construction. Resursosberegayushchie tekhnologii proizvodstva i obrabotki davleniem materialov v mashinostroenii. 2021. No. 4 (37), pp. 106–116. (In Russian).
2. Neustroev D.V., Ovchinnikov I.G. Additive technologies and their application in industrial and transport construction. Vestnik evraziiskoi nauki. 2021. Vol. 13. No. 2, p. 23. (In Russian).
3. Monastyrev P.V., Yezersky V.A., Ivanov I.A., Azzawi Dubla B. Additive technologies for the construction of walls of low-rise buildings and their classification. Moscow: ASV, 2019. Vol. 2, pp. 368–379. (In Russian). DOI 10.22337/9785432303134-368-379
4. Denisova Yu.V. Additive technologies in construction. Stroitel’nye materialy i izdeliya. 2018. Vol. 1. No. 3, pp. 33–42. (In Russian).
5. Slavcheva G.S. Analysis of the Russian regulatory documentation regulating the use and development of construction additive technologies. Stroitel’nye Materialy [Construction Materials]. 2023. No. 8, pp. 10–17. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2023-816-8-10-17
6. Mukhametrakhimov R.H., Vakhitov I.M. Additive technology of construction of buildings and structures using a construction 3D printer. Izvestiya Kazanskogo gosudarstvennogo arkhitekturno-stroitel’nogo universiteta. 2017. No. 4 (42), pp. 350–359. (In Russian).
7. Slavcheva G.S. 3D-build printing today: potential, challenges and prospects for implementation. Stroitel’nye Materialy [Construction Materials]. 2021. No. 5, pp. 28–36. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2021-791-5-28-36
8. De Schutter G., Lesage K., Mechtcherine V., Nerella V.N., Habert G., Agusti-Juan I. Vision of 3D printing with concrete-technical, economic and environmental potentials. Cement and Concrete Research. 2018. Vol. 112, pp. 25–36.
9. Fayzollin M.M., Chernavin V.Yu. Additive technologies for manufacturing floor slabs of large-panel buildings in civil engineering. Nauchnye gorizonty. 2022. No. 5 (57), pp. 80–86. (In Russian).
10. Maitenaz S., Mesnil R., Onfroy P., Metge N., Caron JF. Sustainable reinforced concrete beams: mechanical optimisation and 3D-printed formwork. RILEM International Conference on Concrete and Digital Fabrication. DC 2020: Second RILEM International Conference on Concrete and Digital Fabrication. 2020, Vol. 28, pp. 1164–1173. https://doi.org/10.1007/978-3-030-49916-7_110
11. Anton A., Jipa A., Reiter L., Dillenburger B. Fast complexity: additive manufacturing for prefabricated concrete slabs. RILEM International Conference on Concrete and Digital Fabrication. DC 2020: Second RILEM International Conference on Concrete and Digital Fabrication. 2020. Vol. 28, pp. 1067–1077. https://doi.org/10.1007/978-3-030-49916-7_102
12. Slavcheva G.S., Akulova I.I., Vernigora I.V. Concept and effectiveness of 3D printing for urban environment design. Zhilishchnoe Stroitel’stvo [Housing Construction]. 2020. No. 3, pp. 49–55. (In Russian). DOI: https://doi.org/10.31659/0044-4472-2020-3-49-55
2. Neustroev D.V., Ovchinnikov I.G. Additive technologies and their application in industrial and transport construction. Vestnik evraziiskoi nauki. 2021. Vol. 13. No. 2, p. 23. (In Russian).
3. Monastyrev P.V., Yezersky V.A., Ivanov I.A., Azzawi Dubla B. Additive technologies for the construction of walls of low-rise buildings and their classification. Moscow: ASV, 2019. Vol. 2, pp. 368–379. (In Russian). DOI 10.22337/9785432303134-368-379
4. Denisova Yu.V. Additive technologies in construction. Stroitel’nye materialy i izdeliya. 2018. Vol. 1. No. 3, pp. 33–42. (In Russian).
5. Slavcheva G.S. Analysis of the Russian regulatory documentation regulating the use and development of construction additive technologies. Stroitel’nye Materialy [Construction Materials]. 2023. No. 8, pp. 10–17. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2023-816-8-10-17
6. Mukhametrakhimov R.H., Vakhitov I.M. Additive technology of construction of buildings and structures using a construction 3D printer. Izvestiya Kazanskogo gosudarstvennogo arkhitekturno-stroitel’nogo universiteta. 2017. No. 4 (42), pp. 350–359. (In Russian).
7. Slavcheva G.S. 3D-build printing today: potential, challenges and prospects for implementation. Stroitel’nye Materialy [Construction Materials]. 2021. No. 5, pp. 28–36. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2021-791-5-28-36
8. De Schutter G., Lesage K., Mechtcherine V., Nerella V.N., Habert G., Agusti-Juan I. Vision of 3D printing with concrete-technical, economic and environmental potentials. Cement and Concrete Research. 2018. Vol. 112, pp. 25–36.
9. Fayzollin M.M., Chernavin V.Yu. Additive technologies for manufacturing floor slabs of large-panel buildings in civil engineering. Nauchnye gorizonty. 2022. No. 5 (57), pp. 80–86. (In Russian).
10. Maitenaz S., Mesnil R., Onfroy P., Metge N., Caron JF. Sustainable reinforced concrete beams: mechanical optimisation and 3D-printed formwork. RILEM International Conference on Concrete and Digital Fabrication. DC 2020: Second RILEM International Conference on Concrete and Digital Fabrication. 2020, Vol. 28, pp. 1164–1173. https://doi.org/10.1007/978-3-030-49916-7_110
11. Anton A., Jipa A., Reiter L., Dillenburger B. Fast complexity: additive manufacturing for prefabricated concrete slabs. RILEM International Conference on Concrete and Digital Fabrication. DC 2020: Second RILEM International Conference on Concrete and Digital Fabrication. 2020. Vol. 28, pp. 1067–1077. https://doi.org/10.1007/978-3-030-49916-7_102
12. Slavcheva G.S., Akulova I.I., Vernigora I.V. Concept and effectiveness of 3D printing for urban environment design. Zhilishchnoe Stroitel’stvo [Housing Construction]. 2020. No. 3, pp. 49–55. (In Russian). DOI: https://doi.org/10.31659/0044-4472-2020-3-49-55
For citation: Razov I.O., Sokolov V.G., Dmitriev A.V., Erenchinov S.A. Proposal for the installation of the overlap during the construction of buildings using additive technologies. Stroitel’nye Materialy [Construction Materials]. 2023. No. 10, pp. 116–120. (In Russian). DOI: https://doi.org/10.31659/0585-430X-2023-818-10-116-120